Fiat 480 2wd (55 hp)

 

 

ENGINE POWER:

At flywheel                          55 HP/DIN

 

ENGINE:

Fiat 8035.06

4 - Stroke, 3 Cylinders
Direct Injection Diesel,
Max. Power:     2500 rpm 55HP/DIN (41.0 kw)
Max. Torque:    1500 rpm 185NM (18.88 Kgm)

Dry Type Cylinder Liner

Water Cooling
Bore & Stroke: 100 x 115 mm.
Piston Displacement:    2,710 cc.
Compression Ratio:     17:1

Three row brass tube and copper fin radiator

Force-feed lubrication system

Distributor-type injection pump with mechanical speed governor

Four-Bearing Crankshaft
12 Volt Starting System; 4 hp Motor
400 Watt Alternator
90/95 Ah Battery located in front of radiator
Gearbox Mounted Starter Safety Switch
Vertical Exhaust Muffler

 

OPERATING WEIGHT:

1,710 Kg with 6.00-16 and 12.4/11-28 Tyres, hydraulic lift with three-point linkage cat. 1-2, square type fender with flat top.

 

TRANSMISSION:

Gearbox with Constant-Mesh Gears
Gears:         8 Forward 2 Reverse Speeds
Synchromesh: 3rd, 4th, 7th, and 8th Speeds
Differential with Pedal Actuated Lock 
and Automatic Disconnection.
Single-Reduction Spur Gear Final Drives.

 

SPEEDS (KPH)

With Tyres

Engine speed (rpm)

PTO Speed (rpm)

Forward

first

second

third

fourth

fifth

sixth

seventh

eight

Reverse

first

second

 

 

2160

540

 

1.87

2.82

4.13

5.33

6.75

10.15

14.86

19.20

 

2.69

9.70

12.4/11-28

2500

625

 

2.17

3.26

4.78

6.17

7.81

11.75

17.20

22.22

 

3.11

11.22


STEERING

Manual, recirculation ball type

Centre relay lever

Joints lubricated for life

 

DRIVER'S SEAT

Fully upholstered with parallelogram suspension, adjustable to driver's weight

 

FRONT AXLE

Telescopic type, inverted U, variable tread

 

CLUTCH

Dual Plate, dry type, with separate controls (pedal for transmission and hand lever for PTO)

Diameter of plates: 11 in.

 

POWER TAKE-OFF:

13/8” – 6 Spline Shaft
Fully Independent: 540 rpm at 
2,160 Engine rpm
High-Speed  PTO* (13/8” shaft)
Same Speed as Engine.

* Depends on belt pulley

 

FILTERS

- Air: oil-bath with precleaner and semiautomatic dust unloader

- Fuel: 2 replaceable cartridges

- Oil: easy-to-change, full-flow cartridge

Vertical exhaust muffler

Gearbox mounted starter safety switch

 

FUEL TANK

Capacity: 54 liters

 

HYDRAULIC LIFT

With draft and position control

Draft control through top link

Gear - type pump driven from engine crankshaft

Pump capacity: 22.7 lit/min

Relief valve opening pressure: 150-170 kg/sq. cm.

3-point linkage Cat. 1-2

Manual response control

Lower links with sway restrictors and transverse retaining spring

Control lever with safety stop

Max. lifting capacity: 1540 kg

 

 

TYRES

Front: 6.00-16

Rear: 12.4/11-28

 

LIGHTING SYSTEM

With 3-position headlights; rear position and number plate lights.

2-pole power connector (ASAE)

Blue high beam warning light on dashboard

 

BRAKES

Service: dry, band-type with mechanical control

Parking: with hand lever, on right of operator

 

THREADS

Front (8 positions)

1320 - 1420 - 1520 - 1620 - 1720n - 1820 - 1920 - 2020mm

Rear (8 positions)

1200 - 1300 - 1400 - 1500 - 1600 - 1700 - 1800 - 1900mm

 

DIMENSIONS:

(with 6.00-16 and 12.4/11-28 tyres)

Wheelbase:                                       1,920mm
Overall Length:                                 2,960mm
Height to Top of Hood:                   1,390mm
Height to Steering Wheel:               1,490mm
Front Tread (8 positions):  1,320 – 2,020mm
Rear Tread (8 positions):    1,200 – 1,900mm
Ground Clearance:       480mm under Front Axle

 

OPTIONALS

 

ENGINE

Cold starting aid (Thermostat)

Radiator screen

 

TRANSMISSION

Additional creeper speed reduction unit, for a total of 12 forward and 3 reverse speeds

 

STEERING

Hydrostatic Power, with independent circuit

 

POWER TAKE-OFF

540 rpm (1 3/8" - 6 spline shaft)

Proportional ground speed, revolutions per approx. one metre forward travel (independently of gear engaged): 4.05

 

HYDRAULICS

Auxiliary control valve (right hand) for implement remote control with single or double acting rams

 

TOWING ATTACHMENTS

Swinging drawbar Cat A

Linkage drawbar Cat A-C

 

BELT PULLEY

Diameter:  250mm

Width:  150mm

Pulley speed:  1350 rpm

Belt Speed:  17.7 m/sec

 

OPTIONAL EQUIPMENT:

- Front End Weights with Frame
- PTO Pulley (AGRIPAK Design)

- DTO Pulley
- AGRIPAK SunRoof Canopy (Fiber Glass/Hard Top)
- 9 Hole Draw Bar

- Pintle/Trolley Hook (AGRIPAK Design)
- DTO Suction Pump

- High Clearance Kit

 

 

 

 

For details, please write us here

Home

 

 www.agripak.com.pk @ 2005